Sunday, February 19

Making Bespoke High heels - Part 9 Everything else

The boots are ready :) But there's a lot of phases to be shown, so I decided to make an mega post, showing some of the phases. This is because I already would want to show you all the boots, but I also want to show the whole process. So here's the 32 images. Don't watch this on your phone ;)

First, the moistened uppers are lasted. This is a picture of the first pull to the front.

The bottom view after some  systematic pulling.
After they're dried completely, I marked the line where I wanted the  patent trim to come to.
I then marked the 10mm allowance line.
Now that the uppers were dried, they assumed the shape of the last. Here they are without the lasts, and next came a phase which was logical but seemed totally nuts at the time: cutting the excess leather from the uppers with scissors. Nuts.
But it all made more sense when I glued the patent trim on it and started stitching.
I wanted to show this picture because it shows the "ugly" side of the uppers. The space between the upper and the lining is something no one usually sees. In this image, I'm tying a knot so that the stitching will look  better outwards. Without double stitches, which are the most common way to lock stitch.
Ta-daa!
Before lasting, The wet heel counter goes between the upper and the lining. Glued of course.


And after some sweating, we've reached this far.

The toe cap made from leather is glued on the tip, rasped to the desired shape and compressed with a hammer for minimal thickness.

And everything is wrapped together with adhesive.

After they have dried for another day,  the staples are removed and all that empty space is filled with a cork material.

Here you see the filling after it's been grinded straight. I'm using a traditional heel iron, which has been heated to help me shape that seat for the heel.

The heel quarter is nailed. This will prevent those uppers from  moving in case the glue fails, and helps to keep it together if the heel needs to be replaced.

The heel is covered with 0,5mm thick patent leather. It could've been even thinner, actually.

With the heel put to place with hot glue and the area where the outer sole leather is grinded, the shoes are just waiting for those soles.

I used a pattern to cut the outer sole leather from a 3.0 to 3.5mm thick vegetable tanned sole leather.


The logo is stamped to the damped leather and the surface is shaved with a piece of broken glass.

I pre-shaped the outer soles before applying adhesive.

Adhesive applying.

The leather is carefully placed on the  bottom. Force is used with a hammer and a bone to compress the sole neatly on.

I cut the excess using a special knife.

The rest of the surface is shaved.

The edge is damped with water and prepared with soap for the next phase.

Using a hot iron to make a neat edge.

After a red dye, I painted the edges with black.

Niina wanted some decent cushioning under her ball of the foot. I first thought that this could've been a bit over exaggerating with it... but I was wrong.


Next up was the decorative bow ties. For them I made two small holes for some waxed threads to be used for the fixing of the bows.

The bow ring is made from patent leather and fastened to the shoe with a knot.

Two flat tubes from black alcantara are stuck to the rings... and voilá! Bow ties :D


 Next up, it's the reveal.

12 comments:

  1. Mielenkiintoista nähdä näitä eri vaiheita. On noissa kengissä näköjään tekemistä... Huhhuh.

    ReplyDelete
    Replies
    1. :D Kyllähän niissä on. Tässä on kuvattu vain osa vaiheista eli tekemistä oli todella paljon enemmän mitä kuvat antavat ymmärtää. Noin 90 tuntia meni kaikenkaikkiaan koko projektiin.

      Delete
  2. Tätä työmäärää katsellessa sitä alkaa kyllä miettimään, että mistä kaikesta onkaan mahdettu tinkiä että kiinakenkiä pystytään tuottamaan niin halvalla kuin tuotetaan... Upeat kengät!

    ReplyDelete
    Replies
    1. Kiitos Nefernefernefer :) Noh ensinnäkin teollinen kenkä on aivan oma maailmansa verrattuna tämmöseen "teenpäs ihan kaiken käsityönä" meininkiin. Kyllähän niitä laadukkaitakin popoja tehdasvalmisteisina löytyy. Laatu näkyy yleensä hinnassakin. Tosin luin tuota "Huimaavat korot" kirjaa, jossa kirjoittaja rva. kertoi ettei hinta aina korreloidu laatuun. Hajoavat nekin ilmeisen usein.

      Juttelin alan ammattilaisen kanssa, ja hänen mukaansa kiinasta myydään tehtaalta ulos keskimäärin 6,50€ hintaan pari, josta sitten kaikkien välikäsien jälkeen suomen hyllyyn muodostuu hinnaksi jotain 80-90€.
      Kyllähän mä olen niitä kiinanpopoja monesti silmäillyt ja korjaillutkin. Yleisesti materiaalit ovat halpoja synteettisiä, jolloin ne eivät kestä kulutusta juuri ollenkaan. Eikä niiden tarkoitus olekkaan kestää. Tarkoitus on saada nuorille naisille herätysostos nannaa, jonka voi kohta hajottuaan vaihtaa taas uusiin kohta hajoaviin. Näin saadaan ajallisesti enemmän rahaa lypsettyä kun popoja ei edes kannata korjata.
      Muutenhan jalkineen valmistus menetelmät ovat lähes identtisiä ympäri maapallon. Tingitty on palkoista, materiaaleista sekä volyymi on aivan järkyttävä.

      Delete
  3. Aivan USKOMATTOMAN mielenkiintoista nähdä miten kaiken voi tehdä käsin. Taitaa teikäläiselläkin olla "pari" harjottelutuntia takana, huhhuh!

    ReplyDelete
    Replies
    1. Kiitos kiitos Anonymous :D Joo, tää mun käsillä tekeminen menee vähän turhankin överiksi välillä. Toisaalta nämä ovat ekat mittatilauskorkkarini, oon aikasemmin tehnyt vain noi "eallinit" jotka löytyvät the shoe gallery osiosta oikeasta palkista. Paljon on siis vielä opittavaa, etenkin nopeutta ;)

      Delete
  4. So interesting to see the process you go through... great photos, thanks for going into so much detail, it's fascinating to see!

    ReplyDelete
    Replies
    1. Thank YOU Janine, for your interest and kind words :) I try to give my readers a good look at most of the phases, without making tutorials.

      Delete
  5. Todella upeat kengät! Sopisivat mainiosti omaankin vaatekaappiini. Minkälaisella summalla sinulta saa kenkiä tilattua? Onko hinta eri mittatilauskengille kokonaan omalla idealla, tai vakiintuneelle mallille asiakkaan jalan mukaan?

    T: Heidi

    ReplyDelete
    Replies
    1. Kiitos Heidi! Summissa voi lähestyä emailina maensivushoes/e/hotmail.com. Tällä hetkellähän teen kaiken alusta loppuun käsityönä, eli mallin vaikeus vaikuttaa selvästi käytettävään aikaan. Osittain opiskelujeni puitteissa olisi tarkoitus kokeilla enemmän sarjamaista lähestymistapaa, saa nähdä :)

      Delete
  6. Rakkautta ensisilmäyksellä ( tosin en kyllä ole yksiavioinen kenkien suhteen ;3 )♥ Ihan näin mielenkiinnosta, montako työtuntia näiden tekemiseen meni? Ai että, nyt kyllä alkoi himottamaan mittatilauskengät..

    XoXo Heli

    ReplyDelete
    Replies
    1. Kiitos ja syvä kumarrus sulle Heli :D En tehnyt käytetyistä työtunneista kirjaa, mutta jossain 90 paremmalla puolen heiluttiin. Erittäin haastava malli, joten ylimääräistä aikaa meni monen asian kokeiluun ja uusintoihin.
      Ja jos himo on valtaisa, niin ota ihmeessä yhteyttä maensivushoes/e)hotmail .com, niin katsotaan mitä tapahtuu ;)

      Delete